Use your Xbox Series X|S or Xbox Elite Series 2 controller on PS4 and Switch 1 & 2.
- Easy to use - Just switch the button to change the console mode for PS4 and Switch. Turbo and remap button to set up functions easily
- Supports Audio Function and Motion Control
- Support Turbo and Remap (for PS4/ SW/ PC)
- Emulate PS4 touch Pad Via Function Key
- Supports motion control for PS4 and Switch. 3.5mm microphone headset for PS4 and Xbox One.
Please visit Brook's website to check for firmware updates before using.
Brook X One SE Adapter controller is perfectly compatible to Xbox Series X / S / One, PlayStation 4, Nintendo Switch and PC; motion control and 3.5mm microphone headset are entirely supported.
How to install
- Plug the X One Adapter SE into the lower connector of the controller.
- Flip over to the back of the controller.
- Insert the Micro-USB end of the X One SE cable into the back connector of the X One SE.
- Press and hold the cable so that it is flat against the controller.
- Insert the Type-C end of the X One Adapter SE cable into the top connector of the controller.
How to use on PS4
Toggle the "PS4/Xbox One/Switch slide switch" to where it is labeled "PS".
Wired Connection:
Simply connect the controller to console via X One Adapter SE's "Upgrade/Charge port".
Wireless Connection:
The first time you use the X One Adapter SE, you need to pair it with the wireless controller: go to the "Bluetooth Device" screen and select "Wireless Controller" on your console setting. After waking up the controller, press and hold the "Hold/Wireless pairing button" of X One Adapter SE for 2 seconds to make the LED of X One Adapter SE blink red and blue alternately, and wait for a few seconds until the LED of X One Adapter SE shows a constant blue light. After that, you only need to wake up the controller every time you use the X One Adapter SE.
How to use on Xbox Series X/Xbox Series S/Xbox One/PC
- Toggle the "PS4/Xbox One/Switch slide switch" to the bar labeled between "PS" and "NS".
- In this mode, the X One Adapter SE is set to off, please use the controller as a normal connection.
Note: If you need to use Remap/Turbo/Hold function when connecting to a PC, it is recommended that you connect in PS4 simulation mode.
How to use on Switch
Toggle the "PS4/Xbox One/Switch slide switch" to where it is labeled "NS".
Wired Connection:
Simply connect the controller to console via X One Adapter SE's "Upgrade/Charge port".
Wireless Connection:
The first time you use the X One Adapter SE, you need to pair it with the wireless controller: go to the "Controller" screen on your console. After waking up the controller, press and hold the "Hold/Wireless pairing button" of X One Adapter SE for 2 seconds to make the LED of X One Adapter SE blink red and blue alternately, and wait for a few seconds until the LED of X One Adapter SE shows a constant blue light. After that, you only need to wake up the controller every time you use the X One Adapter SE.
Use of Simulated Touchpad
When using on PS4, press and hold the X One Adapter SE's "Capture/Touchpad Simulate button" and the controller's right analog stick(RS) to simulate touchpad operation.
The default mode of "Capture/Touchpad Simulate button" is "Easy mode", and with RS, you can simulate pressing the touchpad.
However, you can enter "Full mode" temporarily by holding down the "Capture/Touchpad Simulate button"; in this mode, you can simulate more complete touchpad operation; RS simulates the track of sliding on the touchpad, and RSB simulates pressing the touchpad.
If you release the "Capture/Touchpad Simulate button" in "Full mode", it will return to "Easy mode" again.
Turbo Function
Function Settings
- Buttons that can be set as Turbo function buttons include: A, B, X, Y, LB, RB, LT, RT, LSB, RSB(hereinafter referred to as FK).
- Press the "Turbo button" and the FK button at the same time, the controller will vibrate to indicate the successful setting.
- EX: If you press "Turbo button" and "A" button at the same time, then "A" button can be turbo fire.
Cancelling Function
Cancellation of single button turbo function:
- If you press the "Turbo button" and the FK button that has been configured with the turbo function, the controller will vibrate to indicate that the setting is canceled.
- EX: If you press the "Turbo button" and the "A" button at the same time, the "A" button will cancel the turbo fire.
Cancellation of all button turbo function:
- Press and hold the "Turbo button" for 2 seconds, the controller will vibrate 3 times to cancel all the settings.
Delivery
This item is sold and shipped by an Everyday Market Partner. Delivery costs and estimated delivery timeframes are shown on the product page.
Returns
Returns or refunds for Everyday Market items can't be processed in-store. These items are sold and shipped by our Everyday Market Partners, so all returns must be arranged online via Feedback & Enquiry form.
Change of Mind Returns
You can request a change of mind return within 30 days of purchase if your item is in new condition. Items must be unused, undamaged, and returned in their original packaging, including all tags for clothing, footwear and accessories. Some items aren’t eligible for a change of mind return, including bulky items, personal or hygiene-sensitive products, perishables, custom or personalised items, e-gift cards, prepaid SIMs, and dangerous goods. If your change of mind return is approved, a return fee may apply and will be deducted from your final refund. For full details and exclusions, please see our Change of Mind Returns Policy.
Faulty or Damaged Returns
If your item is faulty or arrives damaged, please contact the Everyday Market Partner as soon as possible via Feedback & Enquiry form. Providing clear details and photos will help the Everyday Market Partner assess the issue and work with you to resolve it quickly. Your rights under the Australian Consumer Law still apply.