PF-2 Fluoride Reduction K5350 Filter - Twin Set - for Black Berkey filters - Omnipure

Suits Black Berkey Systems

SET OF BERKEY PF-2 FLUORIDE REDUCTION ELEMENTS FOR USE WITH BLACK BERKEY FILTERS ONLY.

Sold in sets of 2

PF-2 reduction elements, are designed for use with Doulton ceramic filtration elements to adsorb the following four unwanted elements most commonly found in drinking water.

PF elements contain inert high-grade activated alumina, an efficient way for reducing fluoride from drinking water.

PF-2 (previously known as Flow K 5366) Reduction Elements absorb (remove):

• > 95% Fluoride
• Lead, Arsenic, MTBE, DBCP, THMs, Herbicides, Pesticides and Heavy Metal Ions

PF-4 and PF-2 elements are identical in their function. The only difference is that PF-4 elements are needed for use with Super Sterasyl filters (1/4" BSP fitting), while PF-2 elements are required for Black Berkey filters (11mm fitting).

Technical Information:

PF-2 reduction elements are designed for use with Black Berkey filtration elements to absorb the following four unwanted elements most commonly found in drinking water.

• MTBE (Methyl-tertiary-butyl-ether)
• Fluoride
• Lead
• Arsenic

PF filters are also designed to absorb:

• DBCP (Dibromo-chloro-propane)
• THMs (trihalomethanes)
• Herbicides & Pesticides
• Heavy Metal ions

Please note: These filter elements have a specific threading size that will only fit to Black Berkey filters. If you are unsure which filters you need to use, please contact us on 1800 044 722.

• Fluoride: Testing for fluoride was based on 20-30ppm of the ion in the influent aqueous solution at a flow rate of no more than 3 gpm (11 lpm) per cubic foot of media. Results of <1ppm of the fluoride ion in the effluent were typical for the media (>95% reduction). Under optimum conditions, effluent concentrations of less than 50 ppb were readily achieved (>99.75% reduction).
  
  Please note that the average level of fluoride in Australian town water supplies is 1ppm. These filters are what we believe to be most effective as they are tested at a much higher level and are guaranteed for the capacity of the filter. When using these elements in a gravity system, such as our stainless steel or ceramic systems, these filters have longer contact with the media and are therefore more effective than when tested under a higher flow rate.
• Arsenic: This product uniquely targets the entire family of arsenic oxide anions as well as the arsenic cations.
• Lead: Tests have shown that when 7,500 litres of influent water at a concentration of lead of 150-200 ppb pass through 200 grams of media at a flow rate of 1gpm, the lead level was reduced to less than 1ppb (99% reduction).
• MTBE (Methyl-tertiary-butyl-ether): Berkey PF elements are manufactured to exceed ANSI/NSF standard 53, which requires MTBE be reduced by at least two thirds from an influent rate (water going out) of less than 5ppb (>95% reduction*)
  *Actual capacity is dependent on the presence of other competing contaminants in the source water. High levels of total organic carbons and volatile organic compounds may reduce the capacity and efficiency of the elements.

Replacement:

Under normal conditions it is recommended that each PF element be replaced after 1,000 litres (or 2,000 litres if you are using two elements in your system). If you consume about 5 litres of filtered water a day, you would need to replace your filters every 6 months in a system using 1 ceramic filter and 1 element at a time (or every 12 months if using a system using 2 filters and 2 elements).

Actual capacity is dependent on the presence of other competing contaminants in the source water. High levels of fluoride, arsenic and heavy metals may reduce the capacity and efficiency of the elements.

Caution: Elements must be washed and primed BEFORE USE.

Do not install PF Elements before reading installation instructions.

INSTALLATION PROCEDURE

WATCH A SHORT VIDEO ON THE INSTALLATION PROCEDURE HERE

Please note: This video demonstrates the below procedure with a PF-2 element (for Black Berkey elements). The procedure is the same for PF-4 and PF-2 elements.

PRIMING PROCEDURE

The media in your PF elements contain micro fine process dust that can cause the filtered water to have a bitter taste. To dislodge the process dust from your element, it is necessary to prime each element. To prime your element use the following procedure:

1. With blue caps in place wash the exterior of each element with mild dish soap.
2. With clean hands, remove both blue caps from the end of each element.
3. Place the rubber washer (priming button) onto one of the elements and align the hole in the button with the hole in the element. Hold on to your priming button for further priming.
4. Press the priming button up against a sink faucet so that the priming button creates a seal between the faucet and the PF element.
5. While holding priming button against faucet (place thumb on top of faucet to apply pressure and create a better seal), turn on the cold water gently, allowing water to fill the cavity of the PF element and discharge for at least 20 seconds or until water runs clear, whichever is longer.
6. Turn the PF element the other direction and prime the other end repeating steps 3-5. The element has now been primed.
7. Repeat the above steps with the second PF element.

INSTALLATION AND USE:

• Assemble the water filter as per system assembly instruction.
• On the underside of the upper chamber (holding the filter/filters), locate the stem of each filter, making sure the wing nut of th...

Orders leave our warehouse within 1-2 business days.

Delivery time will then be based on Australia Post or the courier used.

Please note that during busy periods (such as major sales and over Christmas), our handling times may increase as we work through orders, however we always do our very best to get everything out as quickly as we can.

After your order has been placed, picked and packed, you will receive an email notification advising you that your order has been shipped. This email will contain your tracking information.

• Metro areas average delivery time frame: 3 - 5 business days
• Regional areas average delivery time frame: 5 - 7 business days
• Remote locations average delivery time frame: 7 - 14 business days
• For accurate delivery times, please visit the Australia Post website Enter the postcode 4313 (that's us) in the 'From' field and your own postcode/country in the 'To' field. Don't forget to include processing time when estimating your delivery date!

All orders sent within Australia require a signature on delivery. If you are not available to sign for your order, Australia Post will leave a note with instructions for pick up from a designated post office. If you are an Australia Post My Post customer you may be contacted by Australia Post prior to delivery offering their Safe Drop service where you waive the requirement for a signature. Note: if you elect to use this service, the agreement is between you and Australia Post, and Nature's Wonderland takes no responsibility for any lost or damaged items due to the use of this service.

While we do everything we can to ensure your order is delivered in a timely manner, we will not be liable for any loss or damage incurred by any person as a result of delay caused by our carrier that we have no control over or by any event which is out of our reasonable control or foresight including, but not limited to, any delay caused by an incorrect delivery address being provided to us.

If you are not fully satisfied with your purchase, you can return your product for a full refund, exchange or repair. Your rights to a remedy under the Australian Consumer Law are not limited by a defined time. However, the Australian Consumer Law does recognise that the relevant time period can vary from product to product, depending on factors such as the nature of the product and the price. Nature's Wonderland adopts the same approach. The type of remedy we can offer you may also vary depending on how long it takes you to return the product to us. At Nature's Wonderland, we will always take a fair and reasonable approach.

To be eligible for a return, your item must be unused and in the same condition that you received it. It must also be in the original packaging.

You are eligible to receive a refund, exchange or repair provided that:

    The product is faulty or is not of acceptable quality
    You receive the wrong product
    The product does not match the photos or description
    The product is in resaleable condition and in its original packaging, including instruction manuals and all accessories, all labels are still attached, and it is not dirty or in otherwise poor condition (unless it arrived as such)

You are not entitled to receive a refund if you:

    Change your mind or decide you no longer want or like the goods
    Are not happy with the performance of the product, when it performs exactly as described
    Found a fault or imperfection when it is clearly listed on the product's page
    Damage the goods after receiving them (provided it is not due to a fault in the item)

If these requirements are not satisfied, Nature's Wonderland reserves the right not to offer an exchange or refund.

In addition, we reserve the right not to offer an exchange, refund or repair where the fault is a result of misuse or neglect.

To complete your return, we require a receipt or proof of purchase.

There are certain situations where only partial refunds are granted:

    Any item not in its original condition, is damaged or missing parts for reasons not due to our error