MCLELLAND 120W 2Ch Amplifier With Dante

120W RMS Two Channel Power Amplifier with Dante

Features

• Stereo into 4-8 Ohm loads
• Bridgeable for 70V or 1 00V (Direct Drive)
• Slot card with integrated Dante receiver
• Power down after -15 minutes of no signal and comply with Energy Star Power consumption limits of < 0.5W in standby
• Yellow LED (Front Panel) to indicated Standby mode is active
• Terminal Block analog audio inputs on 2 CH amp
• 2 x amplifier outputs, bridgeable to 1 channel
• Volume, Auto on/off signal sensing
• Natural cooling without Fan
• TRIGGER could be external remoting ON/OFF
• Short circuit protection
• Overheating protection

Specifications

Dante Audio Interface

• 2x2 audio channels
• I2S digital audio format
• 16, 24 or 32-bit audio samples (per device or per channel)
• 44.1 KHz, 48KHz, 88.2KHz and 96KHz sample rate

Network Interface

• Standard 100Mbps Ethernet
• RMII Ethernet interface with MDIO
• Hardware time-stamping, supporting sample-accurate playback
• Transmit flows: 2 (unicast or multicast)
• Receive flows: 2 (unicast or multicast)
• Latency from 2ms

Amplifier/ Rated Power

• 4ohm Stereo Mode = 120W (22 V) RMS output (steady state). per channel @ < 1 % THD+N
• Bohm Stereo Mode = 120W (31 V) RMS output (steady state), per channel @ < 1 % THD+N
• 70V Bridge Mode= 240 W output (steady state), per channel@ < 1 % THD+N
• 100V Bridge Mode= 240 W output (steady state), per channel@< 1 % THD+N
• 1/8 Rated Power Run Time: continuous operation
• Frequency Response: 20Hz-20kHz +0/-2dB @ 4ohm load
• Signal to Noise: >90dB A WTD
• Dimension: 214mm(W) x 249.Bmm(D) x 44mm(H)

Ship out the order within 24-48 hours.

Change of mind:
Customer can return the item if purchased by mistake within 14 days of the customer’s order being received.

Change of mind returns will only be eligible for a refund on the product’s sale price within receiving the item'. Return postage is paid by the customer.

Warranty

Without prejudice and to the extent allowed by the Trade Practices Act 1974, The Australian Consumer Law and Competition and Consumer Act 2010, all hardware sold by MAD Electronics Australia is covered by one year limited warranty and is also backed by Australian manufacturer warranty. Where the manufacturer warranty period exceeds one year, we will advise the customer to contact the manufacturer directly for warranty support after the first year of purchase. Due to the nature of consumables products and software, they are not returnable or refundable items.

Any defective products purchased from MAD Electronics Australia and affiliates that fall within the warranty period provided will be covered, unless they fall within the following conditions:

· Physical Damage on the product not caused in the event during transit or Dead on Arrival (DOA) but caused due to mishandling, incorrect use of product for its purposes, improper installation of product, by accident, insect or vermin infestation, improper method or failure to maintain service and handle the item with reasonable care.

· The product has been modified using unauthorised methods. Any modifications on the product including physical and software modifications using third party unauthorised software such as third party firmware updates will void the warranty of products.
· The warranty seal or serial number of the item has been tampered with.
· The item has been serviced by another party other than madelectronics
· Consequential loss including but not limited to data, programs, software or other information stored on storage products, computer or laptop systems.
· Software

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.